**Sold Out**For Sale: Air Suction Block Off Plates zl6, zl9, zl10, zg, zx

[zlMark]

Hey guys, I have a very,very limited supply of Brushed Aluminum Air Suction Block Off Plates. Intended for race engines only.:laughing7:

These are very basic in design and serve their intended purpose. All you need to do is remove the old air suction caps, pull the reed plate assy out of the valve cover to grind the screws off that protrude through the reed plate, this is required for the new block off plates to sit flat. Re-install the reed plate the proper way, add a small bead of Ultra Black or other high temp RTV to the mounting surface and install the new block off plates with the included stainless button head allen screws. Or you could remove the valve cover, tap and thread some set screws in valve cover air suction holes. You might even get away with just a thin coat of High Temp RTV on the sealing surface of the new block off plates and leave the reed plates out....up to you! I will be tapping and threading my air suction holes when I have the valve cover off next time. Then to finish you just need some 7/32 vacuum caps for the carbs and if using an airbox drop a nice shiny nickel down in the grommet where the main air suction hose was.

These cost $30 a pair, shipped anywhere in the USA. I will accept paypal to paypal or money orders. PM me for payment details. First come, first served.

[Bacchus]

I got block off plates... a nice touch, and inexpensive too!

[Hellion]

Hey guys, I have a very,very limited supply of Brushed Aluminum Air Suction Block Off Plates. Intended for race engines only.:laughing7:

These are very basic in design and serve their intended purpose. All you need to do is remove the old air caps, pull the reed plate assy out of the valve cover to grind the screws off that protrude through the reed plate, this is required for the new block off plates to sit flat. Re-install the reed plate the proper way, add a small bead of Ultra Black or other high temp RTV to the mounting surface and install the new block off plates with the included stainless button head allen screws.

These cost $30 a pair, shipped anywhere in the USA. I will accept paypal to paypal or money orders. PM me for payment details. First come, first served.

Race engines only??? I have seen alot of KZ's with block off plates and they were basically stock street engines. Why would it be for race porposes only??

[zlMark]

Because you can't remove the emissions and ride the bike on the street....kapeesh?

[prfixer]

Mark- I'll take a pair. PM me your info and I'll get the $$ to you. Dave:headbang:

[Dowee]

I want a pair.

[Jarney]

Because you can't remove the emissions and ride the bike on the street....kapeesh?


From Wikipedia:

Plausible deniability refers to the denial of blame in loose and informal chains of command (http://en.wikipedia.org/wiki/Chain_of_command) where upper rungs quarantine the blame to the lower rungs. In the case that illegal or otherwise disreputable and unpopular activities become public, high-ranking officials may deny any awareness of such act or any connection to the agents used to carry out such act.

:rotf::rotf::rotf::rotf::rotf:

[zlMark]

Yea thats it Jarney!!

[Jarney]

Yeeeeaaahhhh, that's the ticket............hahahaha.

[Hellion]

Because you can't remove the emissions and ride the bike on the street....kapeesh?

Ahhh your state has THOSE regulations. (they dont inspect that stuff here)

[prfixer]

I got my pair, thanks Mark! :headbang:They're already on the NM bike. I do have a question, though. Are you recommending leaving the reeds in just to help with sealing the plates off? I didn't see any other reason to have them in there anymore. Dave

[zlMark]

Yep, just for sealing. I don't want the RTV being the only thing keeping the exhaust in. When I pull the valve cover to do the valve adjustment next time i'll plug the ports with set screws and leave the reed plate assembly out.

[Slippery44]

Got my plates Mark. What a ste.... I mean deal. Thank you again.:headbang:

[zlMark]

Welcome!

[zlMark]

Guys,
I have 3-4 pairs of these left. I need to move these because I am unemployed at the moment and I need to recover my costs on these. So if you are considering buying these please act soon :biggrin:

[markus56]

Bring a pair to Jarneys' tomorrow and I'll get them then!

[prfixer]

Mark- I'll take another pair for the San Diego bike. Not that it'll be ready for them anytime soon, but they'll be nice to have. I'll Paypal you the $$$ here in a minute. Dave

[zlMark]

Bring a pair to Jarneys' tomorrow and I'll get them then!hmmmmm..that sounds like ground shipping by motorcycle carrier.. could get very expensive :biggrin:

Mark- I'll take another pair for the San Diego bike. Not that it'll be ready for them anytime soon, but they'll be nice to have. I'll Paypal you the $$$ here in a minute. Daveon the way!

I have 1-2 pairs left

[zlMark]

gone...........

if anyone wants to have me make another run post here and if there is enough interest i'll have them made

[christoph928]

Utah... Gimmie two. How do I pay you sir..?

[christoph928]

Too late huh..? Let me know if you are gonna do another run...

[Bacchus]

looks like I could use two sets of these... are there going to be any more made?

[DSBeav]

zlMark,

I'd take a pair should you do another run.

Thanks, Don

[markus56]

And I would take two more sets of plates too Mark.

[zlMark]

OK,, maybe i'll do another run of ten

[Bacchus]

can I get mine yesterday?????

[justin jackson]

So what, excactly, do these things do? -and do I (or will I eventually) need them ? race engines only?

[zlMark]

So what, excactly, do these things do? -and do I (or will I eventually) need them ? race engines only?
Justin read this:
http://www.zl-oa.com/forums/showpost.php?p=102794&postcount=7

Really it's a nice neat way to clean up and remove the emissions crap. Not required to do it, but a way of doing it.

[christoph928]

Please sir, may we have some more..?

[zlMark]

I have these ready to ship!

I have 4 orders going out in the morning, who else??????????????

[prfixer]

Mark- I can use another set. I'll Paypal you here in a minute.

[jmassengill]

Mark,
These will fit the 1986 ZL600.....

just wanted you to know...

http://www.zl-oa.com/forums/album.php?albumid=193&pictureid=1759

:headbang:

[42962kevin]

If you have some more available for sale i want a pair.

[zlMark]

Kevin,, sending PM now

[golddrakul]

Mark,

Do you have any of the block off plates left?

[Jim L]

I wanted to know if there are any adverse effects from using these, does the valve cover need to breathe? Does the engine build up pressure or can you cause gasket damage?
I have a set of plates and will be installing them soon.
Jim

[zlMark]

Mark,

Do you have any of the block off plates left?Yes, first come, first serve


I wanted to know if there are any adverse effects from using these, does the valve cover need to breathe? Does the engine build up pressure or can you cause gasket damage?
I have a set of plates and will be installing them soon.
JimThe airsuction adds air to the exhaust port. When you disable it you will notice less popping on decel, therefore it's easier on the gaskets to be rid of it :thumbsup: It has nothing to do with the valve cover breathing, it's completely separate from the crankcase and the top of the head valve area.

The downside is that the unburned gases won't get burned as good resulting in extra hydrocarbons in the atmosphere.

:nike:

[Jim L]

Yes, first come, first serve

The airsuction adds air to the exhaust port. When you disable it you will notice less popping on decel, therefore it's easier on the gaskets to be rid of it :thumbsup: It has nothing to do with the valve cover breathing, it's completely separate from the crankcase and the top of the head valve area.

The downside is that the unburned gases won't get burned as good resulting in extra hydrocarbons in the atmosphere.

:nike:

So the crankcase breather behind the starter takes care of the valve cover breathing as well? As far as unburned gases- I feel better on my bike than in my Silverado, the 6.0 liter is probably worse for the environment!:laughing7:
Jim

[42962kevin]

They were well worth what i spent on them. Got them quick also. I would get them while available i will tell any and everyone. They look great to and also give extra room. Best money i've spent in a long while on the net. Get them.

[zlMark]

All sets of block off plates are gone again. I won't be able to foot the bill to get another run of these made,,unless I hit the mega millions tonight!!

[mplemmons]

Hello,I have a set of these if anybody wants them $30.00 shipped.Let me know if someone wants them.Thanks Mike P.

[tmdoth]

Are any more of these going to be made?

mplemmons.. I might have someone who might want a set for his zx900. I will hopefully know by tomorrow.

[zlMark]

Are any more of these going to be made?

mplemmons.. I might have someone who might want a set for his zx900. I will hopefully know by tomorrow.Greg Couch called me the other day asking if I had a set to sell, lol...I can't foot the bill of another run.

[zl1000 pilot]

:thumbsup: anychance of a set to the uk buddy :thumbsup:

[mplemmons]

Hello give me your address and I'll see if I can send it through the mail.My email is mkplemmons@gmail.com.Thanks .

[Bacchus]

is this item out of stock now?

[zlMark]

**Sold Out**

[kawboy]

Not trying to step on Mark's play, but someone on concours.org said these would work. I have not verified this.

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=300405131537&viewitem=&_trkparms=clkid%3D8401020867677919815

[Jarney]

Those holes look off centered from the whole plate - I'm not not saying they won't work though. These almost look as homemade as the ones I made myself. Later.

[Bacchus]

yeeeeeah .... No

[Billy]

So what does this do for performance 1-2 ...... horse or what ?

[kawboy]

So what does this do for performance 1-2 ...... horse or what ?

Just cleans up the valve cover area - easier maintenance, cleaner look.

[zlMark]

This is the best way to seal off the ports. The next time you remove the valve cover tap the holes to a 5/16", it just takes a 5 turns of the tap to get the set screw seated all the way in.

[mudrunner88]

Mark aren't you worried about debris and / or water pooling in there and causing corosion?

I might plug mine like that then put the block off plates over it.

[zlMark]

Mark aren't you worried about debris and / or water pooling in there and causing corosion?

I might plug mine like that then put the block off plates over it.Yeah thats exactly what I did

[Koz]

Thank you Mark! That was a great way to seal off the ports; I never thought of doing that! I took the valve cover off yesterday and tapped the ports, which was faster than taking off the cover. Great tip!

[zlMark]

Alright who is interested in these? I might do another run.. post up with your quanties wanted!

I think I might have a little bling-bling added to this run, like Eliminator etched into them...

[kawboy]

Alright who is interested in these? I might do another run.. post up with your quanties wanted!



Sorry, bro, got the clean euro valve cover :headbang:

[snap2it]

Hi Mark,

I would like one set please.

Bob

[TruckerEd]

I'll take a set, if you decide to make some more.

[helgi33]

I am interested in one set.
If you go for the bling factor.. then you can engrave similar to these lids sold in Germany. (Just bought two of those..)
http://cgi.ebay.co.uk/BRAKE-RESERVOIR-LID-ELIMINATOR-ZL-600-900-1000-/170585973465?pt=UK_Motorcycle_Parts&hash=item27b7b762d9

[Wissler]

I'll take 1 set for sure.

[Illby1]

I'll take a set for sure!! I was just trying to figure out how I was going to fabricate something because I didn't think you were going to do anymore.

This would be GREAT if you could do another run of them!!!

Thanks!!!
Scotty B

[markus56]

I've still got some of the last run you did but if these were engraved, I'd get a set of those too.

[badbrad]

Count me in for a set also!

[SandstoneSmitty]

I will take a set...

[CHRIS]

i'm in for another set , possibley 2 sets


CHRIS

[jkgonzo]

I would like two sets, engraved would be sweet!!

Thanks........

[Illby1]

Hey Mark, What type of metal do you use for these?? What thickness? Is it stainless? Do you have a place to get it? Depending on what you are using and what thickness,I might be able to look into it and see what kind of price I can get...

Just a thought!!
Scotty B

[zlMark]

Hey Mark, What type of metal do you use for these?? What thickness? Is it stainless? Do you have a place to get it? Depending on what you are using and what thickness,I might be able to look into it and see what kind of price I can get...

Just a thought!!
Scotty B

I don't have one in front of me, but they are aluminum, approx 3/16 thick. the machininist supplies the material.

[zlMark]

Getting a quote from machininist for plates with the "Eliminator" logo lasered in.... stay tuned

[ChiefP]

count me in as well

[snap2it]

Count me in also.

Bob

[tmdoth]

Getting a quote from machininist for plates with the "Eliminator" logo lasered in.... stay tuned

Count me in for a set please Mark.:headbang:

[TruckerEd]

Any update?

[zlMark]

Any update?

Looking at another $5-$10 per set more for the lasering than what I sold them before depending on if I can get them for the same price....Y'all still in?

[snap2it]

Hi Mark,

I am in. I am finding as finish restoring my 900 to her former glory the cleaner I can make that area the better off I will be down the road.

Bob

[prfixer]

I'd take a set for my ZL997 project!

[TruckerEd]

Still in, Rick is sending the carbs back this week. Cant wait to get it back together and hear the thunder

[SandstoneSmitty]

Still in!!!!
I am not much for mods, sooo.... I will need directions on how to install.

[helgi33]

I am as well still in.. do not mind the extra money for the lasering....

[ChiefP]

me too

[Jim L]

I am getting my smooth "German" valve cover powder coated and I will be selling my Gloss Black powder coated valve cover with block off plates already on it. If anyone is interested in it let me know, should be available in about a month... The plates were purchased from Mark last year.

[snap2it]

Hi,

I am interested. Let me know the price. Don't hurt me too bad.

Thanks,

Bob

[TruckerEd]

Any update?

[zlMark]

Workin on it! Will post when i know more

[jdubay]

Interested Jay

[madhatter]

Mark Just want to let everyone know how helpful you have been on here with threads , pictures, video's and such. This forum has been very helpful especially the other guys like kawboy just to name a few I will remember this kindness and brotherhood always thanks alot ..............................